-
悬臂梁MATLAB有限元算例注释
梁可视为平面应力状态,先按图示尺寸划分为均匀的三角形网格,共有8×10=80个单元,5×ll=55个节点,坐标轴以及单元与节点的编号如图。将均布载荷分配到各相应节点上,把有约束的节点5l、52、53、54、55视作固定铰链,建立如图所示的离散化计算模型。(The beam can be regarded as a plane stress state. Firstly, the beam is divided into uniform triangular meshes according to the graphic size. There are 8*10=80 elements, 5*ll=55 nodes. The coordinate axis and the numbering of elements and nodes are shown in the figure. The uniform load is distributed to the corresponding nodes, and the constrained nodes 5l, 52, 53, 54 and 55 are regarded as fixed hinges. The discrete calculation model shown in the figure is established.)
- 2018-12-25 15:34:00下载
- 积分:1
-
基于自适应LMS算法,此程序用于高通滤波器的自适应干扰对消器...
基于自适应LMS算法,此程序用于高通滤波器的自适应干扰对消器-Based on adaptive LMS algorithm, it is used to construct distubance cancler which is cubordilated high_pass filter.
- 2022-03-12 09:18:09下载
- 积分:1
-
一个简单的获取主机名和本机IP地址的程序
一个简单的获取主机名和本机IP地址的程序-A simple access to the host name and IP address of the machine program
- 2022-11-29 11:00:04下载
- 积分:1
-
用c语言在visual C++环境下写的一个扫地雷的游戏
用c语言在visual C++环境下写的一个扫地雷的游戏-Using c language in visual C++ environment, written in a sweep of the game Ray
- 2023-02-22 23:15:04下载
- 积分:1
-
采用生死单元技术模拟焊接动态过程的ansys源程序
采用生死单元技术模拟焊接动态过程的ansys源程序-With life and death cell technology, dynamic process simulation of welding source of ansys
- 2022-01-25 21:23:15下载
- 积分:1
-
steamGuardKeygen
steamGuardKeygen for st
- 2018-02-01 05:02:38下载
- 积分:1
-
1新高考模式下的选课排课问题分析
说明: 新高考模式下的选课排课问题分析matlab完整代码(Matlab Complete Code for Course Selection and Course Scheduling Problem Analysis under the New College Entrance Examination Mode)
- 2020-11-04 20:59:52下载
- 积分:1
-
oled温湿度计
说明: sht30/31驱动stm32f103c8t6 oled屏幕(Sht30/31 drives stm32f103c8t6 OLED screen)
- 2020-06-22 14:00:02下载
- 积分:1
-
SharePoint-Creating-Content-Types-Programmaticall
Creating Content Types Programmatically for SharePoint 2010
- 2014-03-13 08:27:57下载
- 积分:1
-
use of SolidWorks in the secondary development. Is a standard part of a thread a...
使用VB对SolidWorks进行的二次开发。主要是建立了一个螺纹标准件库以及螺纹计算方法。-use of SolidWorks in the secondary development. Is a standard part of a thread and the thread is calculated.
- 2022-05-28 11:02:32下载
- 积分:1